Thermo 2 click

THERMO 2 click carries DS1825, a programmable resolution digital thermometer IC with a unique 64-bit address. The click is designed to run on a 3.3V power supply. The board communicates with the target microcontroller through a 1-wire interface. Using the onboard jumper you can select between two outputs: GP1 (default mikroBUS™ AN pin), and GPO (default PWM pin).

click Product page

Click library

• Author : Stefan Filipovic
• Date : Feb 2022.
• Type : PWM type

Software Support

We provide a library for the Thermo 2 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for Thermo 2 Click driver.

Standard key functions :

• thermo2_cfg_setup Config Object Initialization function.

  void thermo2_cfg_setup ( thermo2_cfg_t *cfg );

• thermo2_init Initialization function.

  err_t thermo2_init ( thermo2_t *ctx, thermo2_cfg_t *cfg );

• thermo2_default_cfg Click Default Configuration function.

  err_t thermo2_default_cfg ( thermo2_t *ctx );

Example key functions :

• thermo2_write_scratchpad This function writes the temperature thresholds and configuration byte to the scratchpad.

  err_t thermo2_write_scratchpad ( thermo2_t *ctx, uint8_t temp_high, uint8_t temp_low, uint8_t config );

• thermo2_read_scratchpad This function reads the scratchpad bytes.

  err_t thermo2_read_scratchpad ( thermo2_t *ctx, uint8_t *scratchpad );

• thermo2_read_temperature This function reads the temperature value in Celsius.

  err_t thermo2_read_temperature ( thermo2_t *ctx, float *temperature );

Example Description

This example demonstrates the use of Thermo 2 click board by reading and displaying the temperature in Celsius.

The demo application is composed of two sections :

Application Init

Initializes the driver and performs the click default configuration.

void application_init ( void )
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    thermo2_cfg_t thermo2_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    thermo2_cfg_setup( &thermo2_cfg );
    THERMO2_MAP_MIKROBUS( thermo2_cfg, MIKROBUS_1 );
    if ( ONE_WIRE_ERROR == thermo2_init( &thermo2, &thermo2_cfg ) )
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }

    if ( THERMO2_ERROR == thermo2_default_cfg ( &thermo2 ) )
    {
        log_error( &logger, " Default configuration." );
        for ( ; ; );
    }

    log_info( &logger, " Application Task " );
}

Application Task

Reads and displays the temperature measured by the click board on the USB UART approximately every 800ms as this matches the required conversion time for 12-bit temperature resolution.

void application_task ( void )
{
    float temperature;
    if ( THERMO2_OK == thermo2_read_temperature ( &thermo2, &temperature ) )
    {
        log_printf( &logger, " Temperature: %.2f C\r\n\n", temperature );
    }
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.Thermo2

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.