Code Categories

All codes (4832)

TOP Contributors

  1. MIKROE (2652 codes)
  2. Alcides Ramos (351 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (112 codes)
  5. Chisanga Mumba (90 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (136614 times)
  2. FAT32 Library (69818 times)
  3. Network Ethernet Library (55883 times)
  4. USB Device Library (46220 times)
  5. Network WiFi Library (41859 times)
  6. FT800 Library (41074 times)
  7. GSM click (28942 times)
  8. PID Library (26401 times)
  9. mikroSDK (26314 times)
  10. microSD click (25327 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Visual TFT/GLCD Project

Mikromedia+ for STM32 ARM - RF Communication Example

Rating:

5

Author: MIKROE

Last Updated: 2013-04-26

Package Version: 1.0.0.0

Category: Communication

Downloaded: 1506 times

Not followed.

License: MIT license  

This is demonstration project how Mikromedia+ for STM communicate over RF. Data is send over simple 'led protocol' (1 byte command). Development board for STM32 with an add-on board nRF Click is used as a receiver device.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Mikromedia+ for STM32 ARM - RF Communication Example" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Mikromedia+ for STM32 ARM - RF Communication Example" changes.

Do you want to report abuse regarding "Mikromedia+ for STM32 ARM - RF Communication Example".

  • Information
  • Comments (0)

Visual TFT/GLCD Project Blog

Mikromedia+ for STM32 ARM

Mikromedia+ for STM32 ARM

Front and back image of Mikromedia+ for STM32 ARM

View full image

Example requirements:
- Development board - EasyMX PRO v7 for STM32 ARM

EasyMX PRO v7 for STM32 ARM

- MCU card with STM32F107VCT6

STM32F107VCT6

- Add-on board: nRF T Click or nRF C Click (used with development system)

nRF C Click
nRF T Click

- Mikromedia+ for STM32 ARM

Mikromedia+ for STM32 ARM

ALSO FROM THIS AUTHOR

SPI Isolator 6 click

0

SPI Isolator 6 Click is a compact add-on board representing a digital isolator optimized for a serial peripheral interface. This board features the MAX22345, a fast, low-power 4-channel digital galvanic isolator from Analog Devices. This device comes with a maximum data rate of 200Mbps and transfers digital signals between circuits with different power domains featuring reinforced isolation for a withstand voltage rating of 3.75kVRMS for 60 seconds.

[Learn More]

V to Hz Click

5

V to HZ click is a device that turns analog voltage into a pulse wave signal of a certain frequency.

[Learn More]

Stepper 12 click

0

Stepper 12 Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB67S549FTG, a two-phase bipolar stepping motor driver from Toshiba Semiconductor. It supports a PWM constant-current control drive without a current sense resistor for motor-current detection and allows full-step to 1/32 steps resolution for less motor noise and smoother control. It has a wide operating voltage range of 4.5V to 34V with an output current capacity of 1.2A maximum and several anomaly detection indicators.

[Learn More]

codegrip for stm32