Brushless 26 click

Brushless 26 Click is a compact add-on board that controls brushless DC motors with any MCU. This board features the DRV8317H, a three-phase PWM motor driver from Texas Instruments. It provides three integrated MOSFET half-bridges for driving three-phase brushless DC (BLDC) motors with 5V, 9V, 12V, or 18V DC rails or 2s to 4s batteries.

click Product page

Click library

• Author : Stefan Ilic
• Date : May 2023.
• Type : I2C type

Software Support

We provide a library for the Brushless 26 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for Brushless 26 Click driver.

Standard key functions :

• brushless26_cfg_setup Config Object Initialization function.

  void brushless26_cfg_setup ( brushless26_cfg_t *cfg );

• brushless26_init Initialization function.

  err_t brushless26_init ( brushless26_t *ctx, brushless26_cfg_t *cfg );

• brushless26_default_cfg Click Default Configuration function.

  err_t brushless26_default_cfg ( brushless26_t *ctx );

Example key functions :

• brushless26_reset_port_exp Brushless 26 reset port expander function.

  void brushless26_reset_port_exp ( brushless26_t *ctx );

• brushless26_set_pins Brushless 26 set pins function.

  err_t brushless26_set_pins ( brushless26_t *ctx, uint8_t set_mask, uint8_t clr_mask );

• brushless26_drive_motor Brushless 26 drive motor function.

  err_t brushless26_drive_motor ( brushless26_t *ctx, uint8_t dir, uint8_t speed, uint32_t time_ms );

Example Description

This example demonstrates the use of the Brushless 26 click board by driving the motor in both directions at different speeds.

The demo application is composed of two sections :

Application Init

Initializes the driver and performs the click default configuration.

void application_init ( void ) 
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    brushless26_cfg_t brushless26_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    brushless26_cfg_setup( &brushless26_cfg );
    BRUSHLESS26_MAP_MIKROBUS( brushless26_cfg, MIKROBUS_1 );
    if ( I2C_MASTER_ERROR == brushless26_init( &brushless26, &brushless26_cfg ) ) 
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }

    if ( BRUSHLESS26_ERROR == brushless26_default_cfg ( &brushless26 ) )
    {
        log_error( &logger, " Default configuration." );
        for ( ; ; );
    }

    log_info( &logger, " Application Task");
}

Application Task

Drives the motor in both directions and changes the motor speed approximately every 2 seconds. The driving direction and speed will be displayed on the USB UART.

void application_task ( void ) 
{
    log_printf ( &logger, "\r\n Driving motor clockwise \r\n" );
    for ( uint8_t speed = BRUSHLESS26_SPEED_MIN; speed <= BRUSHLESS26_SPEED_MAX; speed += 20 )
    {
        log_printf ( &logger, " Speed gain: %u\r\n", ( uint16_t ) speed );
        if ( BRUSHLESS26_OK != brushless26_drive_motor ( &brushless26, BRUSHLESS26_DIR_CW, speed, 2000 ) )
        {
            log_error ( &logger, " Drive motor " );
        }
    }
    Delay_ms ( 1000 );

    log_printf ( &logger, "\r\n Driving motor counter-clockwise \r\n" );
    for ( uint8_t speed = BRUSHLESS26_SPEED_MIN; speed <= BRUSHLESS26_SPEED_MAX; speed += 20 )
    {
        log_printf ( &logger, " Speed gain: %u\r\n", ( uint16_t ) speed );
        if ( BRUSHLESS26_OK != brushless26_drive_motor ( &brushless26, BRUSHLESS26_DIR_CCW, speed, 2000 ) )
        {
            log_error ( &logger, " Drive motor " );
        }
    }
    Delay_ms ( 1000 );
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.Brushless26

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.