TOP Contributors

  1. MIKROE (2663 codes)
  2. Alcides Ramos (358 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (112 codes)
  5. Chisanga Mumba (90 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (137089 times)
  2. FAT32 Library (70232 times)
  3. Network Ethernet Library (56099 times)
  4. USB Device Library (46434 times)
  5. Network WiFi Library (42053 times)
  6. FT800 Library (41383 times)
  7. GSM click (29111 times)
  8. mikroSDK (26560 times)
  9. PID Library (26489 times)
  10. microSD click (25486 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

SpeakUp 3 click

Rating:

0

Author: MIKROE

Last Updated: 2024-04-03

Package Version: 2.1.0.8

mikroSDK Library: 2.0.0.0

Category: Speech recognition

Downloaded: 113 times

Not followed.

License: MIT license  

SpeakUP 3 Click is a compact add-on board providing an offline speech recognition solution. This board features the VC-02, a low-cost pure offline speech recognition module developed by Ai-Thinker Technology. The VC-02 module uses an integrated voice chip US516P6 based on a 32-bit RSIC architecture core, a DSP instruction set for signal processing and speech recognition, an FPU arithmetic unit, and an FFT accelerator. The VC-02 supports offline identification of 150 local instructions, RTOS lightweight system, firmware update feature, as well as the selection of the communication method with the module.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "SpeakUp 3 click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "SpeakUp 3 click" changes.

Do you want to report abuse regarding "SpeakUp 3 click".

  • Information
  • Comments (0)

mikroSDK Library Blog


SpeakUp 3 click

SpeakUP 3 Click is a compact add-on board providing an offline speech recognition solution. This board features the VC-02, a low-cost pure offline speech recognition module developed by Ai-Thinker Technology. The VC-02 module uses an integrated voice chip US516P6 based on a 32-bit RSIC architecture core, a DSP instruction set for signal processing and speech recognition, an FPU arithmetic unit, and an FFT accelerator. The VC-02 supports offline identification of 150 local instructions, RTOS lightweight system, firmware update feature, as well as the selection of the communication method with the module.

speakup3_click.png

click Product page


Click library

  • Author : Stefan Filipovic
  • Date : Sep 2022.
  • Type : UART type

Software Support

We provide a library for the SpeakUp 3 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for SpeakUp 3 Click driver.

Standard key functions :

  • speakup3_cfg_setup Config Object Initialization function.

    void speakup3_cfg_setup ( speakup3_cfg_t *cfg );
  • speakup3_init Initialization function.

    err_t speakup3_init ( speakup3_t *ctx, speakup3_cfg_t *cfg );

Example key functions :

  • speakup3_generic_read This function reads a desired number of data bytes by using UART serial interface.

    err_t speakup3_generic_read ( speakup3_t *ctx, char *data_out, uint16_t len );
  • speakup3_wait_for_reply This function waits up to @b wait_ms for a reply to the voice command.

    err_t speakup3_wait_for_reply ( speakup3_t *ctx, uint8_t *reply_ins, uint32_t wait_ms );

Example Description

This example demonstrates the use of the SpeakUp 3 click board by reading and displaying the voice commands reply messages.

The demo application is composed of two sections :

Application Init

Initializes driver and logger.


void application_init ( void )
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    speakup3_cfg_t speakup3_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    speakup3_cfg_setup( &speakup3_cfg );
    SPEAKUP3_MAP_MIKROBUS( speakup3_cfg, MIKROBUS_1 );
    if ( UART_ERROR == speakup3_init( &speakup3, &speakup3_cfg ) ) 
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }

    log_info( &logger, " Application Task " );
}

Application Task

Waits for the reply message to a voice command and displays it on the USB UART.

void application_task ( void )
{
    uint8_t reply_ins;
    if ( SPEAKUP3_OK == speakup3_wait_for_reply ( &speakup3, &reply_ins, 1000 ) )
    {
        speakup3_display_reply ( reply_ins );
    }
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.SpeakUp3

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.


ALSO FROM THIS AUTHOR

eINK 2.90 inch display

0

eINK click is an adapter Click boardâ„¢, used to interface a compatible eINK display with the host MCU.

[Learn More]

RS485 Isolator 2 click

0

RS485 Isolator 2 Click features ADM2867E a 5.7 kV rms signal and power isolated full duplex RS-485 transceiver.

[Learn More]

Let's make - Thermal Camera

0

Thermal camera project with two different screen resolutions composed of mikroMedia Plus for STM32 and IR Grid click board.

[Learn More]