EERAM 2 click

EERAM 2 Click is a standalone serial SRAM memory that includes shadow non-volatile backup. EERAM uses a small external capacitor to provide the energy needed to move the contents of the SRAM to the non-volatile cells when system power is lost.

click Product page

Click library

• Author : MikroE Team
• Date : Jun 2020.
• Type : SPI type

Software Support

We provide a library for the Eeram2 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for Eeram2 Click driver.

Standard key functions :

• Config Object Initialization function.

  void eeram2_cfg_setup ( eeram2_cfg_t *cfg );

• Initialization function.

  EERAM2_RETVAL eeram2_init ( eeram2_t ctx, eeram2_cfg_t cfg );

Example key functions :

• Set On-hold status function.

  void eeram2_set_on_hold_status ( eeram2_t *ctx, uint8_t en_hold );

• Set command function.

  void eeram2_set_command ( eeram2_t *ctx, uint8_t command );

• Set write status function.

  void eeram2_set_write_status ( eeram2_t *ctx, uint8_t en_write );

Examples Description

This example demonstrates the use of EERAM 2 click board.

The demo application is composed of two sections :

Application Init

Initialization driver enables - SPI.

void application_init ( void )
{
    log_cfg_t log_cfg;
    eeram2_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    eeram2_cfg_setup( &cfg );
    EERAM2_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    eeram2_init( &eeram2, &cfg );

    eeram2_set_on_hold_status( &eeram2, EERAM2_HOLD_DISABLE );
    Delay_ms ( 100 );

    eeram2_set_write_status( &eeram2, EERAM2_WRITE_ENABLE );
    Delay_ms ( 100 );
}

Application Task

Writes a desired number of bytes to the memory and then verifies if it is written correctly by reading from the same memory location and displaying its content on the USB UART.

void application_task ( void )
{
    check_status = eeram2_write_continuous( &eeram2, 0x00543210, &demo_data[ 0 ], 9 );

    if ( check_status == EERAM2_ERROR )
    {
        log_printf( &logger, "   ERROR Writing    \r\n" );
        log_printf( &logger, "--------------------\r\n" );
        for ( ; ; );
    }

    log_printf( &logger, "     Writing...     \r\n" );
    log_printf( &logger, "--------------------\r\n" );
    Delay_ms ( 100 );

    check_status = eeram2_read_continuous( &eeram2, 0x00543210, &read_data[ 0 ], 9 );

    if ( check_status == EERAM2_ERROR )
    {
        log_printf( &logger, "   Reading ERROR    \r\n" );
        log_printf( &logger, "--------------------\r\n" );
        for ( ; ; );
    }

    log_printf( &logger, " Read data : %s", read_data );
    log_printf( &logger, "--------------------\r\n" );

    Delay_ms ( 1000 );
}  

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.Eeram2

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.