templog7  2.1.0.0
Main Page

Temp-Log 7 click

Temp-Log 7 Click is a compact add-on board used to measure and record the temperature of an environment over time. This board features the TMP1826, a high-accuracy, 1-Wire® compatible digital output temperature sensor from Texas Instruments with integrated 2-kbit EEPROM. It supports a wide operating temperature range from –20°C to +85°C with its high accuracy of ±0.1°C (typical)/±0.3°C (maximum) and comes with a factory-programmed 64-bit unique identification number for addressing and NIST traceability. Besides a programmable alarm function that outputs an interrupt signal to the MCU when a specific temperature event occurs, it also has three digital I/O pins configurable for general purposes or to identify the device's position on a shared bus.

click Product page


Click library

  • Author : Stefan Filipovic
  • Date : Mar 2023.
  • Type : One Wire type

Software Support

We provide a library for the Temp-Log 7 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for Temp-Log 7 Click driver.

Standard key functions :

Example key functions :

  • templog7_read_temperature This function starts the one shot measurement and reads the temperature value in Celsius.
    err_t templog7_read_temperature ( templog7_t *ctx, float *temperature );
  • templog7_write_eeprom This function writes a desired number of data bytes to the EEPROM memory.
    err_t templog7_write_eeprom ( templog7_t *ctx, uint16_t address, uint8_t *data_in, uint16_t len );
  • templog7_read_eeprom This function reads a desired number of data bytes from the EEPROM memory.
    err_t templog7_read_eeprom ( templog7_t *ctx, uint16_t address, uint8_t *data_out, uint16_t len );

Example Description

This example demonstrates the use of Temp-Log 7 click board by reading the temperature in Celsius,

then writing the specified data to the memory and reading it back.

The demo application is composed of two sections :

Application Init

Initializes the driver and performs the click default configuration which

clears the EEPROM memory, sets the temperature resolution to 16-bit, enables alert interrupt and sets the temperature alerts to 5 degrees Celsius for low and 40 degrees for high level. Other three IO pins are configured as INPUT.

void application_init ( void )
{
log_cfg_t log_cfg;
templog7_cfg_t templog7_cfg;
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, " Application Init " );
// Click initialization.
templog7_cfg_setup( &templog7_cfg );
TEMPLOG7_MAP_MIKROBUS( templog7_cfg, MIKROBUS_1 );
if ( ONE_WIRE_ERROR == templog7_init( &templog7, &templog7_cfg ) )
{
log_error( &logger, " Communication init." );
for ( ; ; );
}
if ( TEMPLOG7_ERROR == templog7_default_cfg ( &templog7 ) )
{
log_error( &logger, " Default configuration." );
for ( ; ; );
}
log_info( &logger, " Application Task " );
}

Application Task

Reads the temperature in degrees Celsius and the gpio state. After that writes

a desired number of bytes to the memory and then verifies if it is written correctly by reading from the same memory location and displaying the memory content. All data is displayed on the USB UART where you can track changes.

void application_task ( void )
{
uint8_t eeprom_data[ 64 ] = { 0 };
uint8_t gpio_state = 0;
float temperature = 0;
if ( TEMPLOG7_OK == templog7_read_temperature ( &templog7, &temperature ) )
{
log_printf( &logger, "\r\n Temperature: %.2f C\r\n", temperature );
}
if ( TEMPLOG7_OK == templog7_read_gpio ( &templog7, &gpio_state ) )
{
log_printf( &logger, " GPIO state: 0x%.2X\r\n", ( uint16_t ) gpio_state );
}
sizeof ( DEMO_TEXT_MESSAGE ) ) )
{
log_printf ( &logger, " EEPROM write: %s\r\n", ( uint8_t * ) DEMO_TEXT_MESSAGE );
}
if ( TEMPLOG7_OK == templog7_read_eeprom ( &templog7, STARTING_ADDRESS, eeprom_data,
sizeof ( DEMO_TEXT_MESSAGE ) ) )
{
log_printf ( &logger, " EEPROM read: %s\r\n", eeprom_data );
}
if ( !templog7_get_alert_pin ( &templog7 ) )
{
log_info( &logger, " ALERT detected " );
}
Delay_ms ( 1000 );
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.TempLog7

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.


TEMPLOG7_OK
@ TEMPLOG7_OK
Definition: templog7.h:338
templog7_read_gpio
err_t templog7_read_gpio(templog7_t *ctx, uint8_t *data_out)
Temp-Log 7 read gpio function.
templog7_read_eeprom
err_t templog7_read_eeprom(templog7_t *ctx, uint16_t address, uint8_t *data_out, uint16_t len)
Temp-Log 7 read EEPROM function.
templog7_default_cfg
err_t templog7_default_cfg(templog7_t *ctx)
Temp-Log 7 default configuration function.
TEMPLOG7_ERROR
@ TEMPLOG7_ERROR
Definition: templog7.h:339
templog7_read_temperature
err_t templog7_read_temperature(templog7_t *ctx, float *temperature)
Temp-Log 7 read temperature function.
templog7_cfg_setup
void templog7_cfg_setup(templog7_cfg_t *cfg)
Temp-Log 7 configuration object setup function.
application_task
void application_task(void)
Definition: main.c:74
templog7_init
err_t templog7_init(templog7_t *ctx, templog7_cfg_t *cfg)
Temp-Log 7 initialization function.
templog7_get_alert_pin
uint8_t templog7_get_alert_pin(templog7_t *ctx)
Temp-Log 7 get alert pin function.
templog7_t
Temp-Log 7 Click context object.
Definition: templog7.h:303
application_init
void application_init(void)
Definition: main.c:38
STARTING_ADDRESS
#define STARTING_ADDRESS
Definition: main.c:33
templog7_write_eeprom
err_t templog7_write_eeprom(templog7_t *ctx, uint16_t address, uint8_t *data_in, uint16_t len)
Temp-Log 7 write EEPROM function.
DEMO_TEXT_MESSAGE
#define DEMO_TEXT_MESSAGE
Definition: main.c:32
TEMPLOG7_MAP_MIKROBUS
#define TEMPLOG7_MAP_MIKROBUS(cfg, mikrobus)
MikroBUS pin mapping.
Definition: templog7.h:251
templog7_cfg_t
Temp-Log 7 Click configuration object.
Definition: templog7.h:320